Vacuum Strong Shear Type Kneader for High Temperature Vulcanized Silicone Rubber (HTV) Production Machine

Vacuum Strong Shear Type Kneader for High Temperature Vulcanized Silicone Rubber (HTV) Production Machine

Sigma Kneader

 

Double Arm Sigma Kneader is an ideal equipment , design for mixing , kneading , crushing , dispersing high viscosity plastic materials , and has good performance in uniform mixing , no dead ends and high efficiency kneading It has six major components . kneading part , base part , the transmission system , vacuum system , hydraulic system , electric control system , etc .Place of all the contact material is made of stainless steel . There are three choices of oil circulation , electric heating , steam and water cooling.The heating and cooling can be carried out according to the requirements made of the cylinder jacket , wallboard jacket ,stirring blade pass water through hot oil structure . Discharge hydraulic cylinder turned ; screw the material under the loading and other forms .The paddle shaft seal with a unique equilibrium structure of the vacuum tank to prevent the the fillers wear particles into the cylinder , particularly favorable to improve the system vacuum and material purity.It is widely used in many industries : high viscosity sealant , silicone rubber , BMC , adhesive , also , used in batteries , ink , pigments , dyes , pharmaceuticals , resins , plastics , rubber , cosmetics  ects.

Introduction

1) Kneading machine does very well in mixing, kneading, crushing and dispersing for high viscosity liquid materials, with no dead point. 
2)Two sigma or Z-type blades.
3)Equipped with inverter for frequency control.
4)Vacuum and high pressure are available
5)The cylinder is opened hydraulically. 
6)Discharge mode: Hydraulic tilting, Bottom pumping,or Screwing.
7)With jacket outside of the cylinder, for heating or cooling.
8)Heating mode: Hot oil, Electric or Steam.
9)All the parts that contact with material are made of stainless steel.
ABSTER Jacketed Heating Vacuum Kneading Machine (ABSTER-600)

l

Technical parameters

 

Model

 

Chamber Volum(L)

Drive motor power

(KW)

Mixing Speed (rpm)

 Discharge mode

 Heating

Full volume

Feeding amount

Paddle fast / slow paddle

 Optional parameters Optional parameters 

ASM-5

5

3

2.2-4

75/50

Manual / Hydraulic tilting

Running Hot

oil

Electrical heating

Pressure Steam

ASM-20

20

12

3-5.5

63/42

ASM-50

50

30

4-7.5

63/42

ASM-100

100

60

5.5-7.5

43/29

ASM-200

200

120

7.5-15

43/29

Hydraulic tilting

The bottom pumping

Screw extruding

ASM-300

300

180

11-18.5

43/29

ASM-500

500

300

18.5-30

43/29

ASM-1000

1000

600

22-55

32/22

ASM-1500

1500

900

30-90

32/22

ASM-2000

2000

1200

45-110

32/22

ASM-3000

3000 

1800 

55-130 

33/22 

Remarks:

1,Temperature range: 0-300¬į,

2, Pressure range:-0.1-0.6MPa,

3,Inverter for frequency control if necessory.

Available products:

1. Unsaturated resins, alkyd resins, acrylic resins, polyurethane and other complete sets of production equipment;
2. Latex, white latex, rubber coating, film coating, all-purpose adhesive and other complete sets of production equipment;
3. Glass, plastic, silicone rubber, sealants and other sets of production equipment;
4. Raw rubber sets of production equipment;
5. Silicone waste pyrolysis recycling old solvent distillation recovery sets of production equipment;
6. Hot melt adhesive sets of production equipment;
7. Various types of powder mixing auger sets of production equipment;
8. Various non-standard chemical equipment design, production and installation.

FAQ

 

Q : Can you send the formula for the products we want to make ?
A : Our machines can be used for many kinds of product making¬†,such as Resin , Paint,¬†Adhesive , Cosmetic , Food , Chemicals . There¬†are many kinds of these products , so it’s impossible for us to know¬†all the formulas and technologies . We can assist you to find the¬†raw material list you need , and after you place order with us , we can help you to find formula and technology , there will engineers to teach you how to make the product , and the cost will¬†be on your account. ¬†

Q : Do you have machines in stock ?
A : Yes , but just the small-scale machines Machines are different¬†with other products , most of the large-scale machines are¬†designed according to our customers¬†‘requirements different customers have different production requirements , so the¬†technical parameter is different for most machines On the other hands , most of the our machines will cover a large area , so once¬†the machines are finished , we will effect shipment after QC .¬†

Q : Can you send the detailed drawings of the machine to us before we place order ?
A : We can send you a draft drawing of the machines , and after you place order and pay the deposit , our engineer will design the send you the detailed drawings . Once you confirm without questions , we will put it into production.